ONXF-720-BB-42-85-IPX
OneExpert HFC ONXF-720-BB-42-85-IPX DOCSIS 3.1 and Fiber Field Tester with Broadband Power Meter, 42/85 MHz
OneExpert HFC ONX-720 IPX package with 42/85 MHz DOCSIS 3.1 module, broadband optical power meter, VFL and 10 Gbps Ethernet/WiFi 7 testing.
- Package group
- Broadband Power Meter Packages
- Package contents
- Broadband Optical Power Meter, VFL, OneCheck Ethernet, OneCheck WiFi, 10G SpeedCheck, ONX-CATV-D31-S-4285-1012 module (42/85 MHz D3.1), ONX-720 IPX Package, Protective Fitted Case, Cat6A jumper M-F and M-M
- DOCSIS module
- ONX-CATV-D31-S-4285-1012
- Broadband Optical Power Meter
- Included
Overview
The VIAVI OneExpert HFC ONXF-720-BB-42-85-IPX is a new-unit package of the OneExpert HFC (ONX-720/730) handheld platform. It combines DOCSIS, Ethernet, fiber and WiFi 7 testing in one device and validates service throughput up to 10 Gbps, with the platform's OneCheck workflows automating pass/fail testing.
This configuration is an ONX-720 with the IPX software package and the ONX-CATV-D31-S-4285-1012 DOCSIS 3.1 module (42/85 MHz upstream, 1.0 GHz/1.2 GHz downstream). It belongs to the broadband power meter group: it has an integrated broadband optical power meter and a 1 mW visual fault locator, along with OneCheck Ethernet, OneCheck WiFi and 10G SpeedCheck.
DOCSIS and RF
The ONX-720/730 carries over the RF and DOCSIS testing capabilities of the ONX-620/630 and supports existing ONX DOCSIS/RF modules. Test Process Automation guides technicians through installation and troubleshooting steps, so procedures are performed the same way each time.
Design
The unit is IP54 rated, drop tested and modular, with a path to 25G/50G PON and DOCSIS 4.0 upgrades. It also offers integrated GPS, StrataSync and mobile app support, and a field-replaceable 96 W/hr battery.
Key Features
- Broadband optical power meter with 8 calibrated wavelengths
- Visual Fault Locator (1 mW)
- OneCheck Ethernet and OneCheck WiFi 7 included
- VIAVI SpeedCheck to 5 Gbps and 10 Gbps included
- ONX-CATV-D31-S-4285-1012 DOCSIS 3.1 module (42/85 MHz D3.1)
- IPX software package
- Unified OneCheck workflow automates pass/fail for DOCSIS, Ethernet, WiFi, and PON
- Optional Optical Loss mode (set/clear reference with delta)
- Optional optical Ethernet testing over SFP+
- Optional OneCheck PON with GPON/XGS-PON emulation using VIAVI SFP
- Fiber scope support with Auto Analysis for defect detection
- Smart Access Anywhere remote coaching and training (optional)
- IP54 rated, drop-tested, modular design
- Upgradeable for 25G/50G PON and DOCSIS 4.0
- Integrated GPS, StrataSync and VIAVI Mobile Tech app support
- Field-replaceable 96 W/hr Li-Ion battery for multi-day use
Specifications
Package Configuration
| Package group |
Broadband Power Meter Packages
42/85 MHz Upstream 1.0 GHz/1.2 GHz Downstream DOCSIS 3.1 Packages
|
|---|---|
| Package contents | Broadband Optical Power Meter, VFL, OneCheck Ethernet, OneCheck WiFi, 10G SpeedCheck, ONX-CATV-D31-S-4285-1012 module (42/85 MHz D3.1), ONX-720 IPX Package, Protective Fitted Case, Cat6A jumper M-F and M-M |
| DOCSIS module |
ONX-CATV-D31-S-4285-1012
The module list on page 7 gives this module as 'Sweep Ready Module 45/85 MHz 1.0/1.2 GHz', while the ordering pages say 42/85 MHz
|
| Broadband Optical Power Meter | Included |
| PON Selective Optical Power Meter | N/A |
| Optical Loss Mode (Set/clear Ref with Delta) | Opt. |
| Visual Fault Locator (1 mW) | Included |
| OneCheck WiFi7 / OneCheck Ethernet | Included |
| VIAVI SpeedCheck – 5 Gbps / 10 Gbps | Included |
| Ookla Speedtest, VIAVI TrueSpeed, iPerf Speedtest – 5/10 Gbps | Opt. |
| Optical Ethernet Testing over SFP+ | Opt. |
| OneCheck PON w/Emulation – GPON/XGS PON using VIAVI SFP | Opt. |
| Smart Access Anywhere - Remote Connectivity | Opt. |
| IPX Software Package | Included |
| HomeTDR / Home Leakage Test | Opt. |
| Return Signal Generator w/Loopback | Opt. |
| Ingress Expert | Opt. |
| Reverse Sweepless Sweep / QAM Video MPEG Verification / Field View w/RSG | N/A |
Ethernet
| Standard | IEEE 802.3 100M, 1G, 2.5G, 5G, and 10G Ethernet |
|---|---|
| Test Results | Ethernet Frames, IP Connectivity, Ping, Trace route, Web Connectivity, Speed Test up to 10 Gbps |
| 10GBase-T RJ-45 Electrical | 100M, 1G, 2.5G, 5G, 10G |
| SFP+ Optical Ethernet |
1G, 10G (SFP dependent)
optional
|
| SFP+ Electrical Ethernet |
100M, 1G, 2.5G, 5G, 10G
optional
|
WiFi
| OneCheck WiFi (Connected Mode) | WiFi - 7 2x2 (802.11 a/b/g/n/ac/ax/be) 2.4, 5, 6 GHz bands |
|---|---|
| Test Results | Signal strength (RSSI), Standard, Width, Max Router PHY Rate, IP/Web connectivity, Throughput Tests (SpeedCheck, Ookla Speedtest, iPerf) |
Throughput/Performance Tests
| TCP Throughput Test | VIAVI SpeedCheck: 5 Gbps, 10 Gbps; Ookla Speedtest: 5 Gbps, 10 Gbps; VIAVI TrueSpeed (RFC-6349): 5 Gbps, 10 Gbps |
|---|---|
| Performance | Up to 10 Gbps for SpeedCheck, Ookla Speedtest, TrueSpeed, iPerf client: 5 Gbps, 10 Gbps |
| Test Results | Delay, Upstream and Downstream Bit Rates |
Bluetooth Communications
| Communication Interface | Bluetooth v5.0, BLE 2.0 |
|---|---|
| Smart Device Support |
VIAVI Mobile Tech app, Android 8 or newer, iOS12 or newer
recommendation
|
Optical Fiber Scope Support
| USB Optical Fiber Scope | P5000i, FiberChek Probe |
|---|---|
| Results for Zone Defects / Scratches | Pass/Fail |
| Low Mag Field-of-View (FOV) | Horizontal 740 μm, Vertical 550 μm |
| High Mag Field-of-View (FOV) | Horizontal 370 μm, Vertical 275 μm |
| Particle Size Detection | <1 μm |
| Power Source | USB port |
Broadband Power Meter
| Photo Diode | InGaAs |
|---|---|
| Spectral Range | Broadband (800…1650 nm) |
| Wavelength Setting | 850, 980, 1310, 1490, 1550, 1577, 1625, 1650 nm; Custom 800…1650 nm, step size 1 nm |
| Resolution | 0.01 dB, 0.001 μW |
| Measurement Range for Power Level | -65…+10 dBm |
| Max. Power Level | +16 dBm |
| Measurement Uncertainty |
±0.2 dB/±5% (intrinsic)
Under reference conditions: -11 dBm (CW), 1310 nm ±1 nm, 23 °C ±3 K, 45 to 75% relative humidity, SM test fiber (Single Mode, 9 µm core, 8° APC), when used with SC/PC connectors
|
| Measurement Range for PON-ID | N/A |
| Number of Calibrated Wavelengths | 8 (850, 980, 1310, 1490, 1550, 1577, 1625, 1650 nm) |
| Tone Detection |
270 Hz, 330 Hz, 1 kHz, 2 kHz
Future optional capability; received optical power level ≥ -50 dBm; when used with VIAVI Light Source and received optical power level > -50 dBm
|
| Connection | UPP 2.5 mm |
Visual Fault Locator (VFL)
| Fiber Compatibility | Single-mode, Multimode |
|---|---|
| Wavelength | 650 nm (visible) |
| Output Modes | Continuous and flashing |
| Connector Interface | Universal 2.5 mm (fixed) |
| Controls | On/Off Continuous/Flashing |
| Output Power | 1 mW |
| Laser Safety Rating | Class 2 |
| Range (maximum) |
7 km
VFL range depends on many factors, including fiber quality/loss
|
General
| Size |
5.0 x 11.1 x 4.25 in (W x L x H)
ONX-720 and ONX-730 with RF Module
|
|---|---|
| Weight |
3.15 kg (6.9 lb)
ONX-720 and ONX-730 with RF Module, without protective case
|
| Operating Temperature Range | Non-Charging: -10°C to 50°C; Battery Charging: 0°C to 40°C |
| Storage Temperature Range | -20°C to 60°C |
| Operating Humidity Range | 10% to 90% RH, non-condensing |
| For Indoor/Outdoor Use | IP54 light rain (0.5 in/hr; 1.27 cm/hr) |
| Drop Rating | 1 m (3.3 ft) onto concrete |
| Operating Altitude | 4000 m max |
| Pollution | 2° |
| RF immunity |
8.5 V/m
for CATV measurements
|
| DC Input Power | 12 V@5 A |
| DC Charge Port | 2.5 mm barrel |
| Battery | 96 W/hr Li-Ion rechargeable battery, Field replaceable |
| Battery Charge Time | 4 Hrs (90%) 6-8 Hrs 100% (AC charger) |
| Battery Life |
3-5 day typical usage for installation technicians
10 installs a day
|
| USB Host Port(s) | USB-C, USB-A (USB 3.0) |
DOCSIS/RF – Frequency
| Range | 0.5 to 1,218 MHz |
|---|---|
| Accuracy |
±10 ppm
typical @25°C
|
Downstream Analysis — Port 1
| Max Input Power | 60 dBmV total integrated power |
|---|---|
| Operation on Powered TAP | Operate with up to 90 VAC/DC on input port |
| Power Detection/Notification | Notify of AC/DC power presence on port 1 above 2 Volts |
| Return Loss | >9 dB |
| Auto Channel Plan Builder | Auto detection of channels (analog, digital, QAM, OFDM) |
Upstream Analysis — Port 2
| Ingress Spectrum Scan | 0.5–204 MHz, calibrated range 4-204 MHz |
|---|---|
| Sensitivity | −45 dBmV |
| RBW | 300 kHz |
| Min Detectable Level Upstream | −55 dBmV |
| Dynamic Range | 50 dB |
| Max Total Integrated Power | 55 dBmV, 4–10 MHz, 60 dBmV, 10 to 204 MHz |
| Accuracy |
±2 dB
typical at 25°C
|
| Sampling Rate | Hyper Spectrum FFT Gapless technology - no missed samples, spans 0.5 to 110 MHz, 110 to 160 MHz, and 160 to 204 MHz |
| Return Loss | >9.5 dB |
| Operation on Powered TAP | Operate with up to 90 V AC/DC on input port |
| Power Detection/Notification | Notify of AC/DC power presence on port 2 above 2 Volts |
Analog Channel Measurement
| Standards |
NTSC, PAL, SECAM
Video and audio levels (dual)
|
|---|---|
| Min Detectable Signal |
−50 dBmV
single channel
|
| Level Accuracy | ±1.5 dB from −20 dBmV to +50 dBmV typical at 25°C; ±2.0 dB, −20°C to +50°C |
| RBW | 300 kHz |
Downstream Digital Channel Analysis
| Calibrated Power Levels | -20 dBmV to +50 dBmV |
|---|---|
| Level Accuracy | ±1.5 dB from −20 dBmV to +50 dBmV typical at 25°C; ±2.0 dB, −20°C to +50°C |
| Modulation(s) | 64, 128, and 256 QAM, OFDM |
| Symbol rates | Annex A: 5.057 to 6.952 MSPS for 64, 128, and 256 QAM; Annex B: 5.057 MSPS for 64 QAM and 5.361 MSPS for 256 QAM; Annex C: 5.274 MSPS for 64 QAM, and 5.361 MSPS for 256 QAM |
| Regional demods | DVB-C |
| Measurements | Full span MER; Ingress under carrier — full span ingress noise trace; Group delay and in-channel response (ICR); Digital quality index (DQI) overtime; Errored/severely errored seconds; Level, measured symbol rate, carrier frequency, modulation, interleaver depth |
OFDM Signal Performance Metrics
| OFDM Channels | 24-192 MHz wide − up to 3 active OFDM channels |
|---|---|
| Level — max, min, average, standard deviation | Relative to a 6 MHz carrier per CableLabs® |
| MER — max, min, average, standard deviation, percentile | 16 to 44 dB |
| MER Channel Band Graph | Max, min, avg across entire OFDM carrier MER per subcarrier |
| ICFR | In-carrier frequency response (dB) |
| Spectrum/IUC | Spectrum display, including carrier and ingress under carrier |
| Profile Analysis | Profiles A, B, C, D, NCP, and PLC (more profiles as implemented); Lock status, code word errors (corrected and uncorrected) |
MER and BER
| MER specified range |
−5 to +20 dBmV 21 to 40 dB, 64 QAM; 28 to 40 dB, 256 QAM; 16 to 44 dB, OFDM
MER range declines as input levels decrease. Expected MER range at MINLOCK level of –15 dBmV is >30 dB MER.
|
|---|---|
| Max Displayable Range | 50 dB |
| Resolution | 0.1 dB |
| Accuracy |
±2 dB
typical at 25°C
|
| Minimum Lock Level | −15 dBmV |
| BER — Channel Check and DOCSIS Check mode | Down to 1E-9 (pre and post FEC) |
| BER — OneCheck Mode | Down to 1E-8 (pre and post FEC) Std. 1E-9 user selectable |
| Interleaver Depth | 128, 8 max |
RF Module Inputs/Outputs
| RF(2) | F connectors replaceable |
|---|---|
| Port 1 | Downstream 54/85/108/258 MHz depending on diplexer |
| Port 2 | Upstream 0.5–204 MHz and TDR |
| Diplexer 42 MHz |
upstream 4-42 MHz; downstream 54–1,004 MHz
Diplexer return path options may not be available on all units
|
| Diplexer 85 MHz |
upstream 4-85 MHz; downstream 108-1,218 MHz
Also listed: upstream 4-85 MHz; downstream 108-1,004 MHz
|
| MoCA filter | All models have MoCA triplexer to filter out MoCA signals below the highest downstream frequency |
Sweep
| Forward Sweep Telemetry Frequency |
Diplexer dependent 50-1,218 MHz
Input port: Port 1
|
|---|---|
| Forward Sweep Compatibility | SCU-1800 |
| Reverse Sweep Output Transmit Port | Port 1 or Port 2 (user selectable) |
| Port 1 Sweep Frequency Range | Diplexer dependent 5-42/5-65/5-85/5-204 MHz |
| Port 2 Sweep Frequency Range | 5-204 MHz |
| Reverse Sweep Compatibility | SCU-1800 or DAA/RPHY via XperTRAK |
Specifications are taken from the manufacturer's documentation. See the datasheet for complete and current values.
Applications
- Multi-gig residential service activation
- Small business service testing
- DOCSIS 3.1 installation and troubleshooting
- 10G Ethernet throughput validation
- WiFi 7 service delivery testing
- Fiber power level and continuity verification
- Upstream ingress troubleshooting
Included
- ONX-CATV-D31-S-4285-1012 module (42/85 MHz D3.1)
- Broadband Optical Power Meter
- VFL
- OneCheck Ethernet
- OneCheck WiFi
- 10G SpeedCheck
- ONX-720 IPX Package
- Protective Fitted Case
- Cat6A jumper M-F and M-M
Options & Accessories
| Option | Description |
|---|---|
| ONXF-SW-OC-WIFI | OneCheck WiFi Software option |
| ONXF-SW-OC-ETHERNET | OneCheck Ethernet Software option |
| ONXF-SW-SFP-ETH | Enable SFP+ port for Optical Ethernet testing over VIAVI supported SFP's |
| ONXF-SW-OPTICAL-LOSS | Optical Loss test mode option to save reference and calculate loss |
| ONXF-SW-OC-PON | OneCheck PON – PON testing via GPON/XGSPON SFP+ |
| ONXF-SW-OC-GPON-EMUL | GPON Emulation for live service testing on GPON network |
| ONXF-SW-OC-XGSPON-EMUL | GPON Emulation for live service testing on GPON network — Description as printed in the datasheet |
| ONX-SMART-ACCESS | Smart Access Anywhere |
| ONXF-SW-OOKLA-SPD-5G-1Y | ONX Ookla Speedtest to 5 Gbps 1 Yr Timed License/deployed via StrataSync |
| ONXF-SW-OOKLA-SPD-5G-3Y | ONX Ookla Speedtest to 5 Gbps 3 Yr Timed License/deployed via StrataSync |
| ONXF-SW-OOKLA-SPD-5G-5Y | ONX Ookla Speedtest to 5 Gbps 5 Yr Timed License/deployed via StrataSync |
| ONXF-SW-OOKLA-SPD-5G | ONX Ookla Speedtest to 5 Gbps |
| ONXF-SW-OOKLA-SPD-10G-1Y | ONX Ookla Speedtest to 10 Gbps 1 Yr Timed License/deployed via StrataSync |
| ONXF-SW-OOKLA-SPD-10G-3Y | ONX Ookla Speedtest to 10 Gbps 3 Yr Timed License/deployed via StrataSync |
| ONXF-SW-OOKLA-SPD-10G-5Y | ONX Ookla Speedtest to 10 Gbps 5 Yr Timed License/deployed via StrataSync |
| ONXF-SW-OOKLA-SPD-10G | ONX Ookla Speedtest to 10 Gbps |
| ONXF-SW-TRUESPEED-5G-1Y | ONX TrueSpeed to 5 Gbps 1 Yr Timed License/deployed via StrataSync |
| ONXF-SW-TRUESPEED-5G-3Y | ONX TrueSpeed to 5 Gbps 3 Yr Timed License/deployed via StrataSync |
| ONXF-SW-TRUESPEED-5G | ONX TrueSpeed to 5 Gbps permanent License |
| ONXF-SW-TRUESPEED-10G-1Y | ONX TrueSpeed to 10 Gbps 1 Yr Timed License/deployed via StrataSync |
| ONXF-SW-TRUESPEED-10G-3Y | ONX TrueSpeed to 10 Gbps 3 Yr Timed License/deployed via StrataSync |
| ONXF-SW-TRUESPEED-10G | ONX TrueSpeed to 10 Gbps Permanent License |
| ONXF-SW-IPERF-5G-1Y | ONX iPerf test to 5 Gbps 1 Yr Timed License/deployed via StrataSync |
| ONXF-SW-IPERF-5G-3Y | ONX iPerf test to 5 Gbps 3 Yr Timed License/deployed via StrataSync |
| ONXF-SW-IPERF-5G | ONX iPerf test to 5 Gbps Permanent License |
| ONXF-SW-IPERF-10G-1Y | ONX iPerf test to 10 Gbps 1 Yr Timed License/deployed via StrataSync |
| ONXF-SW-IPERF-10G-3Y | ONX iPerf test to 10 Gbps 3 Yr Timed License/deployed via StrataSync |
| ONXF-SW-IPERF-10G | ONX iPerf test to 10 Gbps permanent License |
| ONX-CATV-SW-HL-LKG | Home Leakage Software Option |
| ONX-CATV-SW-HOMETDR | Home TDR Software Option |
| ONX-CATV-SW-RSG-LOOP | Return Signal Generator with Loopback Option |
| ONX-CATV-SW-INGRESS-EXP | Ingress Expert Option for ONX 720's |
| ONX-CATV-SW-RP-SNR-OCE | Return Path SNR in OneCheck Expert - OneExpert CATV |
| ONX-CATV-FWD-SWEEP | Active Forward Sweep |
| ONX-CATV-REV-SWEEP | Active Reverse Sweep |
| NSC-SFP-GPON | GPON SFP for GPON emulation |
| NSC-SFP-XGSPON | XGSPON SFP+ for XGSPON emulation |
| NSC-SFP-850-1G-10G | Optical Ethernet SFP + 850 nm SR 1G and 10G |
| NSC-SFP-1310-1G-10G | Optical Ethernet SFP + 1310 nm LR 1G and 10G |
| NSC-SFP-1550-1G-10G | Optical Ethernet SFP + 1550 nm ER 1G and 10G |
| AC-CHARGER | Replacement AC charger (no power cord) |
| AC-CAR-CHARGER | Car Charger |
| CC-034601 | Large Carrying Case |
| 1019-00-1366 | Strand Hook |
| ONXF-HANDSTRAP | Handstrap for use on unit without a case |
| ONXF-HFC-BATT-96WHR | Replacement 96 W/Hr Battery |
| ONXF-DISPLAY-PROTECTOR-5P | Replacement screen protector (5 pack) |
| ONXF-ETH-ADAPT-M-F | Ethernet Cat6a M-F adapter 0.5 m |
| NSC-ETHERNET-CABLE | Ethernet Cat6a M-M Patch Cable |
| ONXF-HFC-CASE | Fitted protective case for ONX-720/730 with DOCSIS 3.1 |
Documents & Resources
Related Products
FiberChek Probe
VIAVI FiberChek Probe Handheld Fiber Inspection Microscope
Handheld all-in-one fiber inspection microscope with touch screen, auto-focus, auto-center and built-in pass/fail end-face analysis.
INX 660
VIAVI INX 660 Probe Microscope for Automated Single Fiber Connector Inspection
Handheld fiber inspection probe microscope that automates single fiber connector inspection and analysis, with semi-automated multifiber inspection.
Optimeter
VIAVI Optimeter Intelligent Optical Fiber Meter for Fiber Link Certification and Troubleshooting
Optical fiber meter that certifies and troubleshoots a fiber link in under one minute with a single fiber connection and one key press.
SCU-1800
VIAVI SCU-1800 Sweep Control Unit for Headend/Hub CATV Forward and Return Sweep
1RU headend/hub sweep control unit with forward sweep to 1,218 MHz and return sweep to 204 MHz on up to 16 ports.