Anritsu MU909060A Gigabit Ethernet Modules for the MT9090A Network Master

Anritsu / Series · IP/Ethernet Testers

Network Master MU909060A Gigabit Ethernet Modules for MT9090A Mainframe

Gigabit Ethernet test modules for the MT9090A Network Master, covering 10/100/1000 Mbps installation, maintenance and troubleshooting.

Electrical interfaces: 10/100/1000 Mbps RJ 45 (10BASE-T, 100BASE-TX, 1000BASE-T)
Optical interfaces: 100 or 1000 Mbps LC connector (100BASE-FX, 100BASE-LX, 1000BASE-SX, 1000BASE-LX or 1000BASE-ZX)
Interface configuration: Gigabit Ethernet Module with one SFP port and 1 electrical RJ-45 port. One optical module can be installed
Interface configuration: Gigabit Ethernet Module with 2 electrical RJ-45 ports

View Models Datasheet

Overview

The MU909060A Gigabit Ethernet Modules fit the battery-powered Anritsu Network Master MT9090A mainframe. With a module installed, the instrument tests Gigabit Ethernet links during installation and maintenance and helps troubleshoot Ethernet communication lines. It provides bandwidth verification, connectivity testing and service availability verification.

The family has three models with different port configurations. The MU909060A1 has one SFP slot and one RJ-45 port, the MU909060A2 has two RJ-45 ports, and the MU909060A3 has two SFP slots. The two ports can be used at the same time, which shortens installation work across multiple ports and allows pass-through and bidirectional monitoring.

Field operation

The instrument is ready to measure in about 15 seconds and runs for up to 3 hours on a single charge, depending on configuration and setup. It has no fans or vents, and a protector that absorbs shock is supplied as standard. A 4.3-inch wide-screen color display shows results, and a Test Automator together with PASS/FAIL indicators guides users through test sequences. Setups can be stored and copied to other instruments over USB.

Test functions

The modules generate traffic for installation, commissioning and QoS verification, including VLAN-tagged traffic. They also provide BER testing, performance and QoS statistics, service disruption time measurement, and ping and traceroute tests. Optional software adds RFC 2544 testing (including end-to-end testing between two units), ITU-T Y.1564 multi-service testing, Multistream, Stacked VLAN, MPLS, Channel Stats and a Remote GUI that runs in a web browser.

Models in this series

Model	Description
MU909060A1	Network Master MU909060A1 Gigabit Ethernet Module with One SFP Slot and One RJ-45 Port Gigabit Ethernet module for the MT9090A Network Master with one SFP slot and one RJ-45 port for 10/100/1000 Mbps field testing.	Details →
MU909060A2	Network Master MU909060A2 Gigabit Ethernet Module with Two RJ-45 Ports Gigabit Ethernet module with two electrical RJ-45 ports for the MT9090A Network Master, for 10/100/1000 Mbps field testing.	Details →
MU909060A3	Network Master MU909060A3 Gigabit Ethernet Module with Two SFP Slots Gigabit Ethernet module with two SFP slots for the MT9090A Network Master, for field installation and troubleshooting of Ethernet links.	Details →

Key Features

RJ45 and SFP optical interface selectable for two ports
Two ports work simultaneously, including pass through and in-line monitoring tests
Ping test, traceroute test and electrical cable diagnostics
Optional automated ITU-T Y.1564 testing of multiple simultaneous traffic streams
Optional automated RFC 2544 testing, including end-to-end testing
Stacked VLAN (Q-in-Q), MPLS, IPv4 and IPv6 supported
Test Automator for running test sequences
Channel Stats option identifies error streams, top talkers and network attacks
Service disruption time measurement for VoIP and IPTV
Optical power level check and electrical cable test for physical layer testing
Pass/Fail identification and graphical result display
PDF and CSV report generation
4.3-inch high resolution widescreen color display for indoor and outdoor use
Rugged design with no fans or vents
Modular platform
Compact and lightweight design for field portability

Specifications

Interfaces

Electrical interfaces	10/100/1000 Mbps RJ 45 (10BASE-T, 100BASE-TX, 1000BASE-T)
Optical interfaces	100 or 1000 Mbps LC connector (100BASE-FX, 100BASE-LX, 1000BASE-SX, 1000BASE-LX or 1000BASE-ZX)
Interface configuration MU909060A1	Gigabit Ethernet Module with one SFP port and 1 electrical RJ-45 port. One optical module can be installed
Interface configuration MU909060A2	Gigabit Ethernet Module with 2 electrical RJ-45 ports
Interface configuration MU909060A3	Gigabit Ethernet Module with two SFP ports. Two electrical or optical modules can be installed
Duplex modes	Full duplex. Electrical 10/100 Mbps also half duplex
Test configurations	Monitor/Generate, Pass through, Reflector

Optical Modules

1000BASE-SX 850 nm Multi Mode min. input sensitivity and wavelength G0240A	–17 dBm, 770 nm to 860 nm Correct functioning can only be guaranteed with optical modules from Anritsu for the MU909060A
1000BASE-SX 850 nm Multi Mode output power and wavelength G0240A	–9.5 to –1.5 dBm, 830 nm to 860 nm
1000BASE-LX 1310 nm Single Mode min. input sensitivity and wavelength G0241A	–20 dBm, 1260 nm to 1580 nm
1000BASE-LX 1310 nm Single Mode output power and wavelength G0241A	–10 to –3 dBm, 1285 nm to 1343 nm
1000BASE-ZX 1550 nm Single Mode min. input sensitivity and wavelength G0242A	–22 dBm, 1260 nm to 1580 nm
1000BASE-ZX 1550 nm Single Mode output power and wavelength G0242A	–3 to +5 dBm, 1480 nm to 1580 nm
100BASE-FX 1310 nm Multi Mode min. input sensitivity and wavelength G0243A	–31 dBm, 1260 nm to 1570 nm
100BASE-FX 1310 nm Multi Mode output power and wavelength G0243A	–20 to –14 dBm, 1270 nm to 1335 nm
100BASE-LX 1310 nm Single Mode min. input sensitivity and wavelength G0244A	–28 dBm, 1260 nm to 1570 nm
100BASE-LX 1310 nm Single Mode output power and wavelength G0244A	–15 to –8 dBm, 1261 nm to 1360 nm

Traffic Generation

Supported encapsulations	EtherType II (DIX v.2), IEEE 802.3 with 802.2 (LLC1), IEEE 802.3 with SNAP
Line rate	Variable line rate traffic generation, up to full line rate
Traffic shaping	Constant, Burst, Ramped
Frame size modes	Constant, Stepped or Random length
Adjustable frame size	46 to 10,000 bytes
Addressing	Configurable MAC/IP source and destination addresses (supports IPv4 and IPv6), UDP/TCP address and DSCP/TOS byte
DHCP	Request IP source address from a DHCP server (On/Off)
VLAN Option 003	User defined up to 3 level VLAN ID and VLAN priority Option
MPLS Option 004	User defined up to 3 level MPLS label Option
Other generation functions	User defined traffic mix of unicast and broadcast frames; Generate and respond to pause frames; Answer incoming ARP request (On/Off); MAC/IP address swapping (reflector configuration)

Measurements

Test result (current/cumulative)	Total frame, Total bit, Utilization, Throughput, Broadcast frame, Error frame, Frame loss, Frame loss rate
Graph	Tx utilization, Tx throughput, Rx utilization, Rx throughput, Error frame
Service Disruption Time	Min, Max, Average, Count, Total time, Total SDT (%), Last frame received (interval) timestamp
Channel Stats Option 006	Total frame, Total bit, Error, Frame size distribution of up to 63 filtered streams Option
Status / Frame Statistics	Link status, Signal and Frames present (utilization), Errored frames, Rx/Tx frame count, Link time, Remote fault, Speed, Full/Half duplex, MDI/MDIX, Interface type, Link partner abilities (Pause capable and Asymmetric pause capable), Local clock (1000 Mbps), DHCP lease time, Optical level for optical interfaces
Event Log	The instrument logs major events during a test with a 1 sec. resolution time stamp. Logged events include: Link/No link and Test Start/Stop
Report Generation	Generation of test result reports as pdf-files. The report may be customized with a user logo and comments.

Tests

Electrical Cable Test MU909060A1, MU909060A2	Detection of MDI/MDIX mode, Link speed and status, Cable status and distance to fault (if any), Polarity. For 1000 Mbps also skew. Pin mapping: Tx/Rx for 10/100 Mbps, DA, DB, DC, DD for 1000 Mbps
BER Test pattern generation	Unframed, Framed with IP header or Framed with IP and TCP/UDP header Generation and detection of test patterns; count of errors in received test pattern; detection of sequence errors and loss of sequence synchronization
BER Test patterns supported	FOX, all 0, all 1, 0101, PING, PRBS 9, PRBS 11, PRBS 15, PRBS 20, PRBS 23, PRBS 29, PRBS 31, HF test pattern, CRPAT, JTPAT, SPAT
Ping Test	Round Trip Time (RTT); Supports IPv4 and IPv6 addressing; Answer incoming Ping requests (On/Off) For connectivity and configuration check
Traceroute Test	Setup: Number of Attempts, Max number of hops, Number of ping each host, Timeout. Result: Number of hop, Host IP address, Number of Received/Lost replies, Min/Max/Average time
ITU-T Y.1564 test modes Option 007	Single Ended test, Switch/Router test, End-to-End test Option
ITU-T Y.1564 Configuration Test Option 007	Up to 32 services, Up to 6 steps with CBS, EBS. Test result: Pass/Fail, IR (Information Rate), FL (Frame Loss), FTD (Frame Transfer Delay), FDV (Frame Delay Variation) Option
ITU-T Y.1564 Service Performance Test Option 007	Up to 32 services. Test result: Pass/Fail, IR (Information Rate), FL (Frame Loss), FTD (Frame Transfer Delay), FDV (Frame Delay Variation), AVAIL (Availability), UN-AVAIL (Unavailable seconds), SEQ ERR (Sequence Errors) Option
ITU-T Y.1564 test report and parameters Option 007	Test report: Y.1564 Appendix II compliant (CSV or PDF). Parameters: Configurable with MT9090A's Test Automator or the standalone PC application (MX909060A) Option
RFC 2544 single ended and Switch/Router test modes Option 001	Throughput and utilization, Frame loss, Latency, Packet jitter, Back-to-back frames (burstability) Option
RFC 2544 End-to-End network test mode Option 001	Throughput and utilization, Frame loss, Back-to-back frames (burstability) Two MU909060A in an in-band control setup; option
RFC 2544 Router latency test mode Option 001	IP ping based latency, IP ping based packet jitter Option
Multistream Test Option 002	Up to 8 streams can be activated on the Ethernet line; available information per stream: Frame loss count/rate, Frames and bytes received, Frames and bytes transmitted Option
HTTP/FTP Test	Test mode: HTTP, FTP. Setup: Target directory, Download file name, Authentication. Result: Received/Total file size, Min/Max/Average throughput
Reflector delay	2.44 μs @1000 Mbps, 5.16 μs @100 Mbps, 31.93 μs @10 Mbps Maximum internal delay when instrument is in reflector configuration

General

Internal memory	40 MB For storage of results, setups and screen shots
Stored configurations	The user can save a number of configuration files for later recall. The configuration files can be transferred to other instruments via the instruments USB port.
Test Automator	The user can create a macro to run several tests in sequence. The user can also load, save, import and export test macros
Service interface	Two USB 1.1 (One type A for USB memory stick, One type B for USB mass storage)
Display	4.3-inch color LCD (480 × 272 pixels), with LED back light, transmissive
Language	English, Japanese, Chinese (Simplified, Traditional), Spanish, German, Korean, French, Italian, Portuguese

Power

Battery	Dedicated battery pack or 4 AA Ni-MH Indicator for battery level in display when the unit is turned on
Operating time	Up to 3 hours Depending on configuration and test setup
Charging time	4 hours while power off (typ.) Temperature: +10° to +30°C
Power supply	AC adapter: 9 V(dc), 100 V(ac) to 240 V(ac), Frequency: 50 Hz/60 Hz

Physical

Dimensions and mass (module) MU909060A1, MU909060A2, MU909060A3	190 (W) × 96 (H) × 30 (D) mm, <600 g
Dimensions and mass (mainframe) MT9090A	190 (W) × 96 (H) × 18 (D) mm, <200 g

Environmental

Operational temperature range	0° to +40°C, humidity ≤85%, No condensation
Storage temperature range	–25° to +60°C, humidity ≤80%, No condensation
Vibration	IEC 60 068-2-6 Fc and IEC 60 068-2-64 Fh
Ingress protection rating	IEC60529 IP51

Compliance

CE EMC	2014/30/EU, EN61326-1, EN61000-3-2
CE LVD	2014/35/EU, EN61010-1
CE RoHS	2011/65/EU, (EU) 2015/863, EN IEC 63000: 2018
UKCA EMC	S.I. 2016 No.1091, EN 61326-1, EN61000-3-2
UKCA LVD	S.I. 2016 No.1101, EN 61010-1
UKCA RoHS	S.I. 2012 No.3032, EN IEC 63000:2018
Laser safety	IEC 60825-1: 2014 CLASS 1 Complies with 21CFR1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed.3., as described in Laser Notice No. 56, dated May 8, 2014

Applications

Gigabit Ethernet installation and commissioning
Ethernet maintenance and troubleshooting
Carrier class Ethernet
Mobile backhaul testing
QoS verification
VoIP and IPTV service disruption testing
Outside plant field testing

Options & Accessories

Option	Description
MU909060Ax-001	RFC 2544 Test — Including End-To-End testing with master/slave control
MU909060Ax-002	Multistream — Up to 8 streams simultaneous testing
MU909060Ax-003	Stacked VLAN — Up to 3 levels tagged VLAN support
MU909060Ax-004	MPLS — Up to 3 MPLS labels support
MU909060Ax-005	Remote GUI — Controlling MT9090A via Web browser. Requires J1480A USB-Ethernet Converter to connect MT9090A to management Ethernet network
MU909060Ax-006	Channel Stats — Analyzing error streams, top talkers, network attacks
MU909060Ax-007	Y.1564 Test — New methodology to reduce testing time
MU909060A1-301	RFC 2544 Test Retrofit (for MU909060A1)
MU909060A2-301	RFC 2544 Test Retrofit (for MU909060A2)
MU909060A3-301	RFC 2544 Test Retrofit (for MU909060A3)
MU909060A1-302	Multistream Retrofit (for MU909060A1)
MU909060A2-302	Multistream Retrofit (for MU909060A2)
MU909060A3-302	Multistream Retrofit (for MU909060A3)
MU909060A1-303	Stacked VLAN Retrofit (for MU909060A1)
MU909060A2-303	Stacked VLAN Retrofit (for MU909060A2)
MU909060A3-303	Stacked VLAN Retrofit (for MU909060A3)
MU909060A1-304	MPLS Retrofit (for MU909060A1)
MU909060A2-304	MPLS Retrofit (for MU909060A2)
MU909060A3-304	MPLS Retrofit (for MU909060A3)
MU909060A1-305	Remote GUI Retrofit (for MU909060A1) — Requires J1480A USB-Ethernet Converter (sold separately)
MU909060A2-305	Remote GUI Retrofit (for MU909060A2) — Requires J1480A USB-Ethernet Converter (sold separately)
MU909060A3-305	Remote GUI Retrofit (for MU909060A3) — Requires J1480A USB-Ethernet Converter (sold separately)
MU909060A1-306	Channel Stats Retrofit (for MU909060A1)
MU909060A2-306	Channel Stats Retrofit (for MU909060A2)
MU909060A3-306	Channel Stats Retrofit (for MU909060A3)
MU909060A1-307	Y.1564 Test Retrofit (for MU909060A1)
MU909060A2-307	Y.1564 Test Retrofit (for MU909060A2)
MU909060A3-307	Y.1564 Test Retrofit (for MU909060A3)
G0240A	1000 Mbps SX SFP — 850 nm multimode, LC connector (optical)
G0241A	1000 Mbps LX SFP — 1310 nm single mode, LC connector (optical)
G0242A	1000 Mbps ZX SFP — 1550 nm single mode, LC connector (optical)
G0243A	100 Mbps FX SFP — 1310 nm multimode, LC connector (optical)
G0244A	100 Mbps LX SFP — 1310 nm single mode, LC connector (optical)
G0246A	10/100/1000 Mbps RJ-45 SFP (electrical)
Z1580A	Protector & Soft Case — The protector (B0663A) and standard soft case (B0601B) form a set
B0600B	Hard Case — Accommodates two mainframes (with or without fitted protector) and accessories
B0602B	Deluxe Soft Case (for MT9090A) — Full Network Master operation without removal from the case; does not accommodate the mainframe if the protector is fitted
J1402A	Car Plug Cord
W3166AE	MU909060A1/A2/A3 Operation Manual (Hardcopy – English version)
J1480A	USB-Ethernet Converter — Requires MU909060Ax-y05 Remote GUI (sold separately)
MU909060A1-ES210	2 Years Extended Warranty Service (for MU909060A1)
MU909060A2-ES210	2 Years Extended Warranty Service (for MU909060A2)
MU909060A3-ES210	2 Years Extended Warranty Service (for MU909060A3)
MU909060A1-ES310	3 Years Extended Warranty Service (for MU909060A1)
MU909060A2-ES310	3 Years Extended Warranty Service (for MU909060A2)
MU909060A3-ES310	3 Years Extended Warranty Service (for MU909060A3)