MAP mSRC-C2 MSRC-C23000SL-M100-MFA 1310 nm Standard Power SLED Source Module

1310 nm standard power SLED light source module with individual SMF FC/APC output for the VIAVI MAP platform.

Center Wavelength: 1310 nm
Spectral Width (FWHM): > 20 nm; > 30 nm
Output Optical Power: 0 dBm
Optical Power Stability for 15 min: ±0.005 dB

Datasheet

Overview

The MSRC-C23000SL-M100-MFA is a 1310 nm standard power Super-Luminescent Light Emitting Diode (SLED) source with an individual output. It belongs to the VIAVI Multiple Application Platform (MAP) General Purpose Light Source (mSRC-C2) family. The module couples into single-mode fiber and uses an FC/APC connector.

SLED sources combine broadband output with higher power than LEDs. The standard power configuration has an optical power stability of ±0.005 dB. Optical isolators inside the module remove interference effects caused by external reflections. The source is TEC stabilized and runs in either constant current or constant power mode, with at least 10 dB of power tuning range.

Platform

The mSRC is part of the LightDirect module family of the MAP platform. MAP is a modular optical test and measurement platform for rack or benchtop use, with chassis that hold 2, 3 or 8 application modules. It is LXI compliant and comes with SCPI-based automation drivers and a web-enabled multiuser interface. The mSRC-C2 works with all current MAP-300 and MAP-200 chassis.

Key Features

1310 nm standard power SLED source with individual output
Optical power stability of ±0.005 dB for the standard power configuration
Internal optical isolator to reduce dependence on external reflections
TEC stabilized with constant current or constant power control
Optical power tuning range of at least 10 dB
Single-mode fiber output with FC/APC connector
Compatible with all current MAP-300 and MAP-200 chassis

Specifications

Optical Parameters

Center Wavelength	1310 nm Defined as per IEC 61280-1-3 2010 clause 3.1.3, measured at room temperature; all measurements after a minimum of 30 minutes warm-up
Spectral Width (FWHM)	> 20 nm; > 30 nm Standard power SLED values listed across single-wavelength variants; the extracted table does not show which value belongs to 1310 nm. Measured with a resolution bandwidth of 0.06 nm
Output Optical Power	0 dBm Guarantee of 0 dBm excluding connector losses for non-muxed variant
Optical Power Stability for 15 min	±0.005 dB Standard power configuration; ±0.01 dB is listed for multiplexed variants
Optical Power Stability for 3 hours	±0.005 dB Standard power configuration; ±0.01 dB is listed for multiplexed variants
Spectral Ripple (RB = 0.1nm)	0.2 dB
TEC Stabilized	Yes
Wavelength Tolerance	±20 nm
Optical Power Tuning Range	≥ 10 dB From maximum power down
Power Control Mode	Constant Current or Constant Power
Modulation	0.15 to 2.0 kHz Modulation duty cycle is fixed at 50%. Modulation depth is fixed at 100%
Modulation Accuracy	±0.5 Hz
Fiber Type	Single Mode Fiber
Connector Type	FC/APC

General Specifications

Operating Temperature	10 to 40 °C (50 to 104 °F)
Storage Temperature	-30 to 60 °C (-22 to 140 °F)
Operating Humidity	Maximum 85% Relative Humidity, non-condensing from 10 to 40 °C/50 to 104 °F
Dimensions (W x H x D)	4.06 x 13.26 x 37.03 cm (1.6 x 5.22 x 14.58 in)
Weight	1.3 kg (2.86 lb)

Compliance

Safety and Standards	Complies to CE, CSA/ UL/IEC61010-1, LXI Class C requirements, meets the requirements of Class 1M in standard IEC 60825-1 (2014), and complies with 21 CFR 1040.1 except deviations per Laser Notice No. 50 When installed in a MAP chassis

Specifications are taken from the manufacturer's documentation. See the datasheet for complete and current values.

Applications

Broadband sources for use with optical spectrum analyzers
CWDM component measurements
General purpose and interferometry applications
Insertion loss testing
General power sensor or path loss calibration

Options & Accessories

Option	Description
CleanBlastPRO	CleanBlast fiber end-face cleaning system — Optional inspection and cleaning tool for removing dirt and debris from connectors
FiberChek	FiberChek probe microscope — One-button, fully autonomous handheld fiber inspection solution
P5000i	P5000i fiber microscope — Automated Fiber Inspection & Analysis Probe with PASS/FAIL capability
AC500	FC/PC-FC/PC Universal Connector Adapter — Replacement mating sleeve
AC501	FC/PC-SC/PC Universal Connector Adapter — Replacement mating sleeve
AC502	FC/APC-FC/APC Universal Connector Adapter — Replacement mating sleeve
AC503	FC/APC-SC/APC Universal Connector Adapter — Replacement mating sleeve